89 Ranger Replacing Hydraulic Clutch Line - Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars
Ford Forum Ford Forum

» Auto Insurance
» Featured Product
ยป Wheel & Tire Center

Go Back   Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars > Ford Trucks | Utes | Vans |SUVs | Crossovers > Ford Ranger Forum
Register Home Forum Active Topics Photo Gallery Auto Loans Garage Mark Forums Read Auto Escrow

Ford Ranger Forum Forum for discussion of the Ford Ranger.

FordForums.com is the premier Ford Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 09-22-2012, 11:01   #1 (permalink)
Registered User
 
Join Date: Aug 2010
Posts: 81
89 Ranger Replacing Hydraulic Clutch Line

So I have to replace my flywheel, and I noticed my clutch line is kind of corroded inside the slave cylinder.. Is there any way to get the line free from the master cylinder? The new line I got looks like there should be a clip or something holding it in but I dont see anything on the old one.
alden92 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 09-22-2012, 12:37   #2 (permalink)
2002 F150 XLT
 
Bert's Avatar
 
Join Date: Nov 2008
Location: Oregon
Posts: 9,727
Re: 89 Ranger Replacing Hydraulic Clutch Line

It should be like this. There's a picture on the page. 91 Ranger 4x4: hydraulic..clutch..tp use their disconnect tool..mazda - JustAnswer
__________________
Bert
Bert is offline   Reply With Quote
Old 09-22-2012, 13:33   #3 (permalink)
Registered User
 
Join Date: Aug 2010
Posts: 81
Re: 89 Ranger Replacing Hydraulic Clutch Line

I was looking to disconnect it from the master cylinder, I talked to a guy from ford and he said theres a roll pin, but I cant seem to get it out.. I tried pushing it up and down and it wont move either way... Are there any other tricks I could try? All I could find small enough to push it was an allen wrench, maybe I can get a small screwdriver or something and try that.. Any suggestions would be appreciated.
alden92 is offline   Reply With Quote
Old 09-22-2012, 14:24   #4 (permalink)
2002 F150 XLT
 
Bert's Avatar
 
Join Date: Nov 2008
Location: Oregon
Posts: 9,727
Re: 89 Ranger Replacing Hydraulic Clutch Line

On the master cylinder, the roll pin has to be tapped out with a punch, then just pull the line out.
__________________
Bert
Bert is offline   Reply With Quote
Old 09-22-2012, 14:40   #5 (permalink)
Registered User
 
Join Date: Aug 2010
Posts: 81
Re: 89 Ranger Replacing Hydraulic Clutch Line

does it matter which way you push the pin out? I'm gonna go get a punch for it..
alden92 is offline   Reply With Quote
Old 09-22-2012, 14:42   #6 (permalink)
2002 F150 XLT
 
Bert's Avatar
 
Join Date: Nov 2008
Location: Oregon
Posts: 9,727
Re: 89 Ranger Replacing Hydraulic Clutch Line

It doesn't matter. Just use the easiest to get to.
__________________
Bert
Bert is offline   Reply With Quote
Old 09-22-2012, 14:45   #7 (permalink)
Registered User
 
Join Date: Aug 2010
Posts: 81
Re: 89 Ranger Replacing Hydraulic Clutch Line

ok. the reason I asked is the guy from ford said he wasnt sure if it had to be pushed up or down to come out..
alden92 is offline   Reply With Quote
Old 09-22-2012, 15:54   #8 (permalink)
2002 F150 XLT
 
Bert's Avatar
 
Join Date: Nov 2008
Location: Oregon
Posts: 9,727
Re: 89 Ranger Replacing Hydraulic Clutch Line

Look at the other side to see whare it'll come out.
__________________
Bert
Bert is offline   Reply With Quote
Old 09-22-2012, 16:18   #9 (permalink)
Registered User
 
Join Date: Aug 2010
Posts: 81
Re: 89 Ranger Replacing Hydraulic Clutch Line

I know the hole goes all the way through, I put a allen wrench all the way through it earlier before I talked to the ford guy thinking maybe it would release it that way.. I'm just not sure of its the same size all the way through allowing it to come out the other side.. and I cant see the other side unless I take the master cylinder completely out to twist it around...
alden92 is offline   Reply With Quote
Old 09-22-2012, 19:27   #10 (permalink)
2002 F150 XLT
 
Bert's Avatar
 
Join Date: Nov 2008
Location: Oregon
Posts: 9,727
Re: 89 Ranger Replacing Hydraulic Clutch Line

The you know which way to tap it out. The punch has to be able to "just" fit in the hole to push it out.
__________________
Bert
Bert is offline   Reply With Quote
Sponsored Links
Advertisement
 
Reply

  Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars > Ford Trucks | Utes | Vans |SUVs | Crossovers > Ford Ranger Forum



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Powered by vBadvanced CMPS v3.2.2

All times are GMT -7. The time now is 14:42.



Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO 3.6.0
Garage Plus vBulletin Plugins by Drive Thru Online, Inc.