Upper/Lower intake - Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars
Ford Forum Ford Forum

» Auto Insurance
» Featured Product
ยป Wheel & Tire Center

Go Back   Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars > The Garage - Tech Forums > Engine Specific Tech > Windsor Tech
Register Home Forum Active Topics Photo Gallery Auto Loans Garage Mark Forums Read Auto Escrow

FordForums.com is the premier Ford Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 10-28-2003, 01:39   #1 (permalink)
Registered User
 
Join Date: May 2003
Posts: 50
Upper/Lower intake

I was thinking about getting a trickflow upper and lower intake for my eb v8 but i also found out that edelbrock make a upper and lower intake as well. What set would be the best? also what sort of power increase would i be looking at and whatprice would i be looking at??

Thanks
Falcon SXR8 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 10-28-2003, 02:37   #2 (permalink)
345kw of V8 Windsor Power
 
EDXR8's Avatar
 
Join Date: Jul 2001
Location: Adelaide
Age: 35
Posts: 2,784
Re: Upper/Lower intake

Both the Edelbrock and Trickflow intakes should set you back about $1100. Trickflow advertise they flow around 245cfm per runner while Edelbrock are around 220cfm. Personally I would probably go for the Edelbrock because 1) 220cfm should be enough for around 300kw 2) Edelbrock say they don't loose any low down torque and 3) trickflows have had problems with head to intake leaks, although I don't know if they are fixed by now. Either one will give you good results though. Also, what heads are you running, because if they are still the stock E7 heads, the intake won't make a huge difference.
EDXR8 is offline   Reply With Quote
Old 10-28-2003, 03:39   #3 (permalink)
Two SC 61's = trouble
 
ebxr8240's Avatar
 
Join Date: Jul 2001
Location: Penrith,nswAus/Morrinville.NZ
Age: 61
Posts: 6,360
Re: Upper/Lower intake

Most the issues with Trickflow leaks was due to builders fitting too thick gasget in valley between heads.If you check on there site it says to use silicon sealant for this reason..
Exactly these are heavy breathing inlets but better even flow to one and five cyl compared to std type inlets..
__________________
Don't be afraid to try something new. Remember, amateurs built the Ark...Professionals built the Titanic!
.
Tuned & maintained by "Peppertree Perfmormance". Dart block, Scat 4340 steel crank, Custom C.P pistons.Oliver rods.. Mal Wood twin plate clutch.. Twin SC61/2's,482 rwkw/ 645 rwhp..
Passengers, myocardial infarction material..
R.I.P Possum...
ebxr8240 is offline   Reply With Quote
Old 11-01-2003, 13:43   #4 (permalink)
3FB Educator!
 
B-1B's Avatar
 
Join Date: Mar 2003
Location: Educating some of the brothers
Posts: 527
Re: Upper/Lower intake

I have Trick Flow street inlet and Twisted Wedge heads and have had NO problems.Done about 25,000kms with this combo and am very happy!Definatly would recomend them.
__________________
There's a bear in there.
Due to the graphic nature of this programme
listener discretion is advised
B-1B is offline   Reply With Quote
Sponsored Links
Advertisement
 
Reply

  Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars > The Garage - Tech Forums > Engine Specific Tech > Windsor Tech



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
replacing upper intake manifold MKII240T Windsor Tech 38 06-18-2004 19:20
Intake Question - Pod or Airbox... Axeman82 General Tech 1 12-17-2002 13:57
GT40 upper intake on Cobra lower intake xr8_sprint General Tech 5 11-11-2002 02:06
my 94 intake... jaygecko Ford Ranger Forum 2 10-24-2001 15:11
3.0L Intake (Prototype for Production) Vulcan Power V6 and Hot4 Tech 3 05-07-2001 01:46

Powered by vBadvanced CMPS v3.2.2

All times are GMT -7. The time now is 09:02.



Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO 3.6.0
Garage Plus vBulletin Plugins by Drive Thru Online, Inc.