My F250 won't start - Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars
LinkBack Thread Tools Display Modes
post #1 of 3 (permalink) Old 12-30-06, 05:10 PM Thread Starter
Registered User
Join Date: Dec 2006
Posts: 3
My F250 won't start

I have a 1991 F250 7.3L Diesel that has decided to stop starting... hopefully, someone here can make some suggestions. When I try to start the truck, the solenoid clicks once and then everything electrical dies. I had the starter bench tested at AutoZone and they say that it is fine, as are the batteries (tested also). I connect the two battery wires to the solenoid and leave it hanging rather than connecting it the fly wheel... one solenoid click and nothing. I replaced the stupid "Ford" solenoid on the fender of the truck (I don't know why Ford insists on two solenoids but that can be for another post) - one click solenoid and nothing. I took a jumper cable and went between the + post of one battery and the corresponding post on the starter's solenoid... this time I get one solenoid click, a few (5-6) cranks and then nothing. The wire on the jumper cable heats up and starts melting the plastic sheath (I think if it was heavy enough gauge that jumping the battery to the solenoid would work). My dad tells me to check all the cable connections (+/- wires)... I checked and cleaned all the (+) connections with a wire wheel on a grinder or sandpaper so they are all clean (bare metal). I didn't check or clean the engine or frame grounds because I think that if I had a ground issue, my battery to starter solenoid jumping would produce the same results as without the jumping... I did nothing to the ground when I run the jumper cable. My next option is to replace the battery cables... I call Ford and they want $300 for the cables (are you f-ing kidding me? I understand copper is expensive but how does the dealership justify that price?), AutoZone wants $110... note about the cable; the (-) cables are pretty standard, the (+) cable is connected to the left-hand battery, runs to the right-hand battery, and then splits. From here, one wire (16 gauge) goes to the "Ford" fender solenoid and then goes to the starter solenoid; the other wire (4 gauge) goes to another post on the starter solenoid. I am going to wait until Tuesday to see how much a battery shop can make the cable for me, but before I do that, am I missing something that I can check or change? Could my jumper between the (+) on one terminal to the starter solenoid really work if I had a ground issue? Again, when I do this, all the battery wires are connected as they would be from the dealership. I generally drive the truck to tow my boat only; this all happened when I took it for a drive (ran about 20 min) and then turned it off outside of a store... hasn't started since.

saltydog73 is offline  
Sponsored Links
post #2 of 3 (permalink) Old 12-30-06, 07:05 PM
Always the student
thefonz's Avatar
Join Date: Jul 2006
Posts: 1,738
Re: My F250 won't start

Most likely cause is a bad connection. You said you did all the positive cables, but you need to do the neg. cables as well. The wires can also be bad under the insulation. It could also be either solenoid,(you can by pass the solenoid for test purposes). Don't forget... it is possible to get bad parts even though they are new
thefonz is offline  
post #3 of 3 (permalink) Old 12-31-06, 05:49 PM
Registered User
Join Date: Dec 2006
Location: Albany GA.
Posts: 2
Re: My F250 won't start

I agree; it sounds like lack of a good connection. The usual problem with auto electrical circuits is not the feed, but the ground. The other things which i would have suggested are; 1. your column ignition, but you said you jumped the starter and bypassed it. 2. Neutral \ clutch switch - also would have been bypassed. 3. You have a hydraulic or mechanical tie-up - unlikely since you had just run it earlier, but if it was running hot, or your oil pressure was bad, it's not impossible.
SSAutoGroup is offline  
Sponsored Links

  Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars > The Garage - Tech Forums > Engine Specific Tech > Diesel Tech

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode

Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

For the best viewing experience please update your browser to Google Chrome