Escape trouble code P0200 - Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars
Ford Forum Ford Forum

» Auto Insurance
» Featured Product
ยป Wheel & Tire Center

Go Back   Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars > Ford Trucks | Utes | Vans |SUVs | Crossovers > Ford Escape | C-MAX | Mercury Mariner Forum
Register Home Forum Active Topics Photo Gallery Auto Loans Garage Mark Forums Read Auto Escrow

Ford Escape | C-MAX | Mercury Mariner Forum This forum is for discussion of the Ford Escape, C-MAX, the Ford Escape Hybrid and the Mercury Mariner.

FordForums.com is the premier Ford Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 09-02-2011, 18:58   #1 (permalink)
Registered User
 
Join Date: Sep 2011
Location: Arkansas
Age: 50
Posts: 2
Escape trouble code P0200

Hey out there, I am a first time user.......have a P0200 code in my son's 02 Escape XLT that comes on when he gets onto freeway and stays off after cleared with city driving. What is going on?
wadesescape is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 09-03-2011, 04:21   #2 (permalink)
Registered User
 
Sterling_Six's Avatar
 
Join Date: Aug 2008
Location: Green Bay, WI
Posts: 1,135
Re: Escape trouble code P0200

Quote:
Originally Posted by wadesescape View Post
Hey out there, I am a first time user.......have a P0200 code in my son's 02 Escape XLT that comes on when he gets onto freeway and stays off after cleared with city driving. What is going on?
Hello and good day:

P0200 O2 Sensor Circuit No Activity

OBD-II Trouble Code Technical Description

Injector Circuit Malfunction
What does that mean?

In sequential Powertrain Control Module controls each injector individually. Battery voltage is supplied to each injector from, usually, the power distribution center (PDC) or other fused source. The PCM supplies the ground circuit to each injector by means of an internal switch called a "driver". The PCM monitors each driver circuit for faults. For example, when a fuel injector is commanded "off" by the PCM, it expects to see a high voltage on the driver ground circuit. Conversely, when a fuel injector is commanded "on" by the PCM, it expects to see the voltage pulled low on the driver circuit
If it doesn't see this expected condition on the driver circuit, P0200 or P1222 may set. Other injector circuit fault codes may set as well.

Symptoms

Symptoms of a P0200 DTC may include:
  • <LI itxtNodeId="44" itxtHarvested="0">MIL (Malfunction Indicator Lamp) illumination <LI itxtNodeId="43" itxtHarvested="0">Engine misfire at idle or at highway speed <LI itxtNodeId="42" itxtHarvested="0">Engine may start and stall or not start at all
  • Cylinder misfire codes may be present
Causes

Potential causes of an P0200 code include:
  • <LI itxtNodeId="50" itxtHarvested="0">Open or shorted injector <LI itxtNodeId="49" itxtHarvested="0">Injector low internal resistance (basically an injector that works, but is out of specs) <LI itxtNodeId="48" itxtHarvested="0">Grounded driver circuit <LI itxtNodeId="47" itxtHarvested="0">Open driver circuit <LI itxtNodeId="46" itxtHarvested="0">Driver circuit shorted to voltage
  • Wiring harness intermittently shorting against underhood components
Possible Solutions

1. If you have multiple misfire/injector codes, a good first step is to unplug all the fuel injectors and then turn the ignition on, engine off (KOEO). Check for presence of battery voltage (12 Volts) at one wire of each injector connector. If all are missing, check for continuity to ground on the voltage circuit by using a test light connected to positive battery and probe each voltage feed. If it lights up, then there is a short to ground on the voltage feed causing a short. Get a wiring diagram and repair the short on the voltage feed and reestablish proper battery voltage. (Don't forget to check for a blown fuse and replace as necessary). NOTE: It's possible for one injector to short out the whole battery voltage feed to all the injectors. So if you have lost voltage to all the injectors, replace the blown fuse and plug each injector in, one by one. If the fuse blows, the last injector you plugged in is shorted. Replace it and retest. If only one or two battery feeds are missing, then it's more likely to be a shorted battery voltage feed in the individual injector wiring harness. Inspect and repair as necessary.
2. If you have battery voltage fed to each injector harness, then the next step is to get a noid light to check for injector driver operation. A noid light will insert into the injector harness in place of the fuel injector and flash rapidly when the injector driver operates. Check each fuel injector connector. If the noid light flashes rapidly then suspect the injector. Ohm each fuel injector if you have a resistance specification. If the injector is open or the resistance is higher or lower than the spec, replace the fuel injector. If the injector tests out, the problem is likely an intermittent wiring problem. (Remember that a fuel injector can work properly when cold but go open when hot, or vice versa. So it's best to do these checks when the problem is occurring). Check the wiring harness for any chafing, or the injector connector for loose pins or a broken lock. Repair as necessary and retest. Now, if the noid light doesn't flash, then there's a problem with the driver or the driver circuit. Unplug the PCM connector and ohm the fuel injector driver circuits. Any resistance means there's a problem. Infinite resistance points to an open in the circuit. Find it and repair it, then retest. If you can find no problem with the harness and there is no fuel injector driver operation, then check the PCM powers and grounds. If they are okay, the PCM may be at fault.
Article written by Dale Toalston
__________________
Good Luck and good repairing Sterling_6
"You know, just like in that Book, When Jesus beats up Moses to get Religion!!"
Sterling_Six is offline   Reply With Quote
Old 09-03-2011, 09:01   #3 (permalink)
Registered User
 
Join Date: Jul 2011
Location: Athens, TX
Posts: 11
Re: Escape trouble code P0200

Nice reply - Sterling Six! This is what this forum is all about. Maybe a bit technical but right to the point. I wish more feedback form others on this site but it does not happen. I belong to the Lexus forum and usually get replies back no more than a day after the inquiry. Keep up the good work.
Fordy4 is offline   Reply With Quote
Old 09-04-2011, 12:03   #4 (permalink)
Registered User
 
Join Date: Sep 2011
Location: Arkansas
Age: 50
Posts: 2
Re: Escape trouble code P0200

Thanks!!! Guess I will take it to a mechanic. Too technical for me to spend alot of time trying to trouble shoot, just don't have the knowledge base to tackle it.
wadesescape is offline   Reply With Quote
Sponsored Links
Advertisement
 
Reply

  Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars > Ford Trucks | Utes | Vans |SUVs | Crossovers > Ford Escape | C-MAX | Mercury Mariner Forum



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Powered by vBadvanced CMPS v3.2.2

All times are GMT -7. The time now is 18:44.



Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO 3.6.0
Garage Plus vBulletin Plugins by Drive Thru Online, Inc.