Ford Forums is the premier Ford Forum on the internet. We discuss all Ford models on the forum. Registered Users do not see the above ads. Please Register - It's Free!
I have a ford contour1996,2.0,4cyl.I have replaced the ignition coil,& i am
having problems with starting it,have to keep my foot on the gas,will not
idle too.is there any thing i can do before taking it to the shop??
> I have a ford contour1996,2.0,4cyl.I have replaced the ignition coil,&
> i am having problems with starting it,have to keep my foot on the
> gas,will not idle too.is there any thing i can do before taking it to
> the shop??
>
>
idle speed control valve
if you are handy and have a few metric wrenches, you can change it yourself
--
Yeh, I'm a Krusty old Geezer, putting up with my 'smartass' is the price
you pay..DEAL with it!
Re starting & idleing.Thanks Krusty,today i finally changed the IACV on the
contour also fuel filter,still having the same problems.there is a flat
device directly on the left just below the air filter,it is some switch
made of aluminum,has a six pin plug,it has something to do with the
ignition??
1996 Ford contour,2.0 4 cyl.I ahve a problem with starting it,it only
starts when you gave it gas,also will not idle.I have change the coil,fuel
filter,& idle air control valve,yet it continues to not work right,it also
shows service engine light.Any suggestions out there Please.
> 1996 Ford contour,2.0 4 cyl.I ahve a problem with starting it,it only
> starts when you gave it gas,also will not idle.I have change the
> coil,fuel filter,& idle air control valve,yet it continues to not work
> right,it also shows service engine light.Any suggestions out there
> Please.
>
Engine Lite! did it do that before?
Would have helped!
Go to autozone or a parts store that reads out diagnostic codes free... get
the code, not their description.
Just for fun, FIRST, though.. after the engine has warmed, turn off and
unplug the MAF.. which is in the air tube to manifold and located just near
the filter. See if it starts and idles, then.
--
Yeh, I'm a Krusty old Geezer, putting up with my 'smartass' is the price
you pay..DEAL with it!
Hey thanks old buddy ,yes the engine light did this in the past, sometimes
stays on,then it will dissappear but returns after weeks ,months etc.I
will get back at you,after i try same. Thanks.
hey again,i did what you said after warming up engine & turning off same i
unplugged the MAF & started it again ,it struggled to start,it sounded
like a big piece of junk,idle almost as if was going to shut off,also
rough idle & if it was missing a beat at times.The check engine lite
remains on.But it did start & idle.
> hey again,i did what you said after warming up engine & turning off
> same i unplugged the MAF & started it again ,it struggled to start,it
> sounded like a big piece of junk,idle almost as if was going to shut
> off,also rough idle & if it was missing a beat at times.The check
> engine lite remains on.But it did start & idle.
>
Then you certainly have more than 1 problem, but start with cleaning the
MAF
Remove the security screws with small vise grips.
alcohol and new paint brush clean, rinse repeat works fine, do not bump
element
--
Yeh, I'm a Krusty old Geezer, putting up with my 'smartass' is the price
you pay..DEAL with it!
Hey I did clean the Maf still not working right,I took it to auto zone & it
read a code p402,they said it's the egr valve however i am getting a hard
time disconecting it,I got the two bolts out,but the tube at the base of
the egr i cannot get to.any solutions?? thank you
> Hey I did clean the Maf still not working right,I took it to auto zone
> & it read a code p402,they said it's the egr valve however i am
> getting a hard time disconecting it,I got the two bolts out,but the
> tube at the base of the egr i cannot get to.any solutions??
> thank you
>
Dunno
havent pulled on for years.
Suggest heating it.
--
Yeh, I'm a Krusty old Geezer, putting up with my 'smartass' is the price
you pay..DEAL with it!
Linear Mode
