Turbochargeing MX6 ??? - Page 2 - Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars
Mazda Forum This area is for discussion of Mazda vehicles

Reply
 
LinkBack Thread Tools Display Modes
post #11 of 24 (permalink) Old 11-07-03, 10:51 PM
Faster than Zyrtec
 
dave_au's Avatar
 
Join Date: Nov 2002
Location: Sydney.
Age: 36
Posts: 2,105
Re: Turbochargeing MX6 ???

Oh, and also, Zoom magazine a while back had the 2.5L engine with twin turbos sitting in a drag racing commodore - 750Bhp - they did do some internal mods to the engine, cams etc, cant remember the full details. Probably about 12 months ago now.

dave_au is offline  
Sponsored Links
Advertisement
 
post #12 of 24 (permalink) Old 11-07-03, 10:57 PM Thread Starter
Two SC 61's = trouble
 
ebxr8240's Avatar
 
Join Date: Jul 2001
Location: Penrith,nswAus/Morrinville.NZ
Age: 65
Posts: 6,360
Re: Turbochargeing MX6 ???

Yes I must have a look at one. Eunos.. I dought the std blower would have much cfm though, but a good place to start...

The reason I said V6 is the earlier ones where 4 cyl...Less room with V6..
Thanks Dave...

Don't be afraid to try something new. Remember, amateurs built the Ark...Professionals built the Titanic!
.
Tuned & maintained by "Peppertree Perfmormance". Dart block, Scat 4340 steel crank, Custom C.P pistons.Oliver rods.. Mal Wood twin plate clutch.. Twin SC61/2's,482 rwkw/ 645 rwhp..
Passengers, myocardial infarction material..
R.I.P Possum...
ebxr8240 is offline  
post #13 of 24 (permalink) Old 11-16-03, 03:16 PM
Probe GT
 
Join Date: Dec 2001
Location: Santa Cruz, Cali
Age: 35
Posts: 47
Re: Turbochargeing MX6 ???

wait so it's a 92 mx6 kl03? or is it f2? If it's a 92 should have the f2. If its a v6 it should be 93 at least

is it a euro model or something?

I could probably recomend some sites but it depends on what engine/car you have.

Eric
E-Betz is offline  
Sponsored Links
Advertisement
 
post #14 of 24 (permalink) Old 11-17-03, 03:20 AM Thread Starter
Two SC 61's = trouble
 
ebxr8240's Avatar
 
Join Date: Jul 2001
Location: Penrith,nswAus/Morrinville.NZ
Age: 65
Posts: 6,360
Re: Turbochargeing MX6 ???

Yes I think that Commodore sports sedan was built by Austrack out at Minto NSW..Alittle over the top for street use. These engines [blocks] must be bulletproof!!!

Its a 92 2.5 V6/ 24 quad cam, manual... first model here in Australia with this motor.Previous mx6's were 4 cyl and not a patch on this model, it still looks good over 10 years latter...

Don't be afraid to try something new. Remember, amateurs built the Ark...Professionals built the Titanic!
.
Tuned & maintained by "Peppertree Perfmormance". Dart block, Scat 4340 steel crank, Custom C.P pistons.Oliver rods.. Mal Wood twin plate clutch.. Twin SC61/2's,482 rwkw/ 645 rwhp..
Passengers, myocardial infarction material..
R.I.P Possum...
ebxr8240 is offline  
post #15 of 24 (permalink) Old 12-12-03, 05:26 PM Thread Starter
Two SC 61's = trouble
 
ebxr8240's Avatar
 
Join Date: Jul 2001
Location: Penrith,nswAus/Morrinville.NZ
Age: 65
Posts: 6,360
Re: Turbochargeing MX6 ???

The injecters are not combatable with anything else ? Does any one know how to fit bigger injecters higher than 220cc ?? Looks like we have to convert the fuel rails to custom ones from SR 20 etc or fit extra inj's at throttle body...

Don't be afraid to try something new. Remember, amateurs built the Ark...Professionals built the Titanic!
.
Tuned & maintained by "Peppertree Perfmormance". Dart block, Scat 4340 steel crank, Custom C.P pistons.Oliver rods.. Mal Wood twin plate clutch.. Twin SC61/2's,482 rwkw/ 645 rwhp..
Passengers, myocardial infarction material..
R.I.P Possum...
ebxr8240 is offline  
post #16 of 24 (permalink) Old 12-12-03, 06:24 PM
Registered User
 
Join Date: Nov 2003
Location: south morang vic
Posts: 17
Re: Turbochargeing MX6 ???

im an apprentice spray painter and yesterday we were spraying an mx6 all wheel steer turbo but im not exactlysure what model it was and im 100% sure it was a factory turbo

like what kentucky means to chickens
lokt.eb is offline  
post #17 of 24 (permalink) Old 12-15-03, 04:58 AM Thread Starter
Two SC 61's = trouble
 
ebxr8240's Avatar
 
Join Date: Jul 2001
Location: Penrith,nswAus/Morrinville.NZ
Age: 65
Posts: 6,360
Re: Turbochargeing MX6 ???

Yes mate thats why I said V6 for the early ones where 4 cylinders, some where turbo'd..We have the parts except injectors so we are going to add two at throttle body.Have taken 2.5cc out of each chamber. Using GT 40 turbo .70 AR cold side and .62 turbine side.. EB on N2O is making up exhaust manifolds.Using existing cast manifolds to turbo.300 X 600mm intercooler.This is going on a latter model motor KLz with wilder cams inlet etc..Just hope we can work out how to run different coil/ dissy set up??

Don't be afraid to try something new. Remember, amateurs built the Ark...Professionals built the Titanic!
.
Tuned & maintained by "Peppertree Perfmormance". Dart block, Scat 4340 steel crank, Custom C.P pistons.Oliver rods.. Mal Wood twin plate clutch.. Twin SC61/2's,482 rwkw/ 645 rwhp..
Passengers, myocardial infarction material..
R.I.P Possum...
ebxr8240 is offline  
post #18 of 24 (permalink) Old 02-19-04, 01:14 AM
Fast but not Furious
 
Mr. Mx6's Avatar
 
Join Date: Feb 2004
Location: Australia
Age: 47
Posts: 44
Re: Turbochargeing MX6 ???

The injectors from the eunous v6 have a higher flow rate.. I think the import ones are millennia’s?..
Any way they are a few members mx6 .com with boosted v6 now..
Come on over and have a look around..
Mr. Mx6 is offline  
post #19 of 24 (permalink) Old 03-06-04, 05:05 AM Thread Starter
Two SC 61's = trouble
 
ebxr8240's Avatar
 
Join Date: Jul 2001
Location: Penrith,nswAus/Morrinville.NZ
Age: 65
Posts: 6,360
Re: Turbochargeing MX6 ???

Got some injectors off a s/c V6 929 it has 29cc injectors I guess same as Millena's...Thats around 300cc...

Don't be afraid to try something new. Remember, amateurs built the Ark...Professionals built the Titanic!
.
Tuned & maintained by "Peppertree Perfmormance". Dart block, Scat 4340 steel crank, Custom C.P pistons.Oliver rods.. Mal Wood twin plate clutch.. Twin SC61/2's,482 rwkw/ 645 rwhp..
Passengers, myocardial infarction material..
R.I.P Possum...
ebxr8240 is offline  
post #20 of 24 (permalink) Old 03-09-04, 06:59 PM
Australian Probe Member
 
Join Date: Jul 2001
Location: Sydney, Australia
Age: 56
Posts: 841
Re: Turbochargeing MX6 ???

Try this link to the Forced Induction section of ProbeTalk:

http://forums.probetalk.com/forumdisplay.php?f=101

1997 Alpine Green Probe, 18mm Swaybar, Custom Yellow & Black Italian Leather Interior, CD Stacker, Yellow Wiper Blades, Ford Australia 75th Anniversary Sticker & Badge, PRD Wires & Sills
2008 Blue Ambition Mondeo XR5, Bluetooth for work
DRU842 is offline  
Sponsored Links
Advertisement
 
Reply

  Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars > Ford Cars and PAG Vehicles > Mazda Forum


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome