Ford Forums banner

Search results

1-20 of 370 Results
Advanced Search
  1. xp ute

    Classic Falcons
    Hi! Theres been a bit of discusion on this subject before and the answer is yes you can make one fit No its not bolt in. check this link http://www.fordforums.com/showthread.php?t=103698&highlight=steering
  2. Fuelstar???????????????

    Classic Falcons
    Yeah i know :priest: I had a good chuckle when i read it. but they are minuscule particles of metallic tin .so they might be able to fit more in.
  3. Fuelstar???????????????

    Classic Falcons
    5kg of lead compared to 5kg of tin would look like less but not much . lead 11.34 g/cm3 Tin 7.31 g/cm3 As a coating the tin would cover more area so you would need less. those cannisters still arn't big enough :priest:
  4. Fuelstar???????????????

    Classic Falcons
    IT uses a tin catalyst.and is supposed to last 500,000 km's. from there web site So the tin is supposed to do the job that lead did . If you used leaded fuel for 500,000 km's then you would have used around 5 kilos of lead . So how big is that cannister? :whoaa:
  5. xp falcon resto

    Classic Falcons
    Is the diff set up for Holden wheels?? The std diff is supposed to be 56 inches wide . When i got my Xm it was fitted with a Xt 8inch(59inches) and XC 4wheel disks Im wating on some new axles as im fitting one shortened to 55 inches which is as short as you can go with the stock leaf spring...
  6. "BOSS"?

    Windsor Tech
    Any competent machine shop could do the mods. [A] Coolant passages need to be plugged. [B] 0.80 inch hole must be drilled on each head. Use the SVO intake as a template for these holes. [C] Remove these alignment pegs. [D] Use freeze plugs to block these end holes, if the heads have them. 6...
  7. XK falcon questions

    Classic Falcons
    Use the bolt in engine cross member that was fitted to xm,xp's to strenghen the front end. A few years back i fitted a alloy head crossflow engine/bw35 trans into an xm the original xm engine mounts bolt straight on and a modified gearbox crossmember was all that was needed, there wasn't...
  8. Windsor power increase. Where to start?

    Windsor Tech
    Your bov isn't meant to vent into the cabin, you need some fresh air to clear your mind. a cam with around 210-220deg duration @.050 and .49 lift should wake it up. around $400 for parts cam, lifters ,springs gaskets cheaper if your lucky http://www.cranecams.com.au/caminfo/ford351302.htm#351
  9. "BOSS"?

    Windsor Tech
  10. "BOSS"?

    Windsor Tech
    The Ford Boss 302 engine was a performance variant of the Windsor, putting what would become Cleveland heads on the Windsor block to improve rated power to 290 hp (216 kW). According to some reports, the engine could produce more than 310 hp(231 kW), although as delivered, it was equipped with...
  11. oil squirting but from where?

    Windsor Tech
    Hi 302junkie, how about the oil pressure sender ? if it happening when your driving the oil could be getting blown towards the rear. I would give everything a good wash and take it for a spin .Then check to see where the fresh oil is. just an idea. good luck
  12. efi onto carbi 302w

    Windsor Tech
    Brendon if you go EFI with a factory manifold you will need to do something with the strut tower braces as the passanger one is in the way of the manifold upper. or do what Atec77 said with the custom upper.
  13. stumped...

    Windsor Tech
    The thermostat housing is attached to the inlet manifold on windsors . and the block on clevelands
  14. Tattoos. Whos got one??

    The Pub
    I think you will find that tattoo's and the way in which they are done have improved quite a bit in 30 YEARS Just like every thing else has, I remember watching tv on our brand new black and white TV ,wouldn't want now though :hy:
  15. Mystery Car week 14

    The Pub
    I think its the car Noddy and Big Ears cruise around in.
  16. Tattoos. Whos got one??

    The Pub
    Ive got a few. This is my favorite one :nerner:
  17. Limit of stock Ford 8" diff

    Trans | Driveline
    The 8inch with traction lock was used in the XT GT falcon
  18. How heavy is it????

    E-Series Falcons
    I think you will find it closer to 1500kg's
  19. RECOIL - Chris's XA Project (WARNING - Not Dial Up Friendly)

    Classic Falcons
    Inspiring Stuff indeed! Its great to see someone taking the time to bring a classic back to life. To see the amount of work thats involved is amazing ,its made me feel a bit more confident when it comes time to rip into mine. The green looks excellent! with or without the stripes. :hy:
  20. $200,000 Ford Fairlane

    The Pub
    I love that car!
1-20 of 370 Results
Top